You are reading the article Ps4 Dualshock Controller Not Charging? 10 Ways To Fix updated in December 2023 on the website Katfastfood.com. We hope that the information we have shared is helpful to you. If you find the content interesting and meaningful, please share it with your friends and continue to follow and support us for the latest updates. Suggested January 2024 Ps4 Dualshock Controller Not Charging? 10 Ways To Fix
The PS4 might be getting on in years, but there are still over 100 million consoles worldwide and many more PS4 DualShock controllers than that!
If your trusty controller won’t charge or hold its charge as long as it used to, there are a few things you can do about this common problem before considering a complete replacement.
Table of ContentsNormal Charge Times and Battery Life
Before we look at the troubleshooting steps for your DualShock 4 controller not charging, it’s important to establish a baseline for what’s normal.
The DS4 should charge from empty to full in around two hours. The battery should last four to eight hours, depending on the game and your controller settings. Dimming the light bar and disabling the rumble can extend the controller’s battery life. If your controller is constantly running out of juice in less than four hours, this is a sign that something isn’t right.1. Make Sure Rest Mode Charging Is Active
Of course, when you turn your PS4 off, you should choose rest mode rather than turning the console off completely, or it won’t charge the controllers either.2. Updating Firmware (You Can’t!)
One potential fix for issues with a DualShock 4 is to update its firmware like you can with an Xbox Series or PlayStation 5 controller. However, as far as we can tell, there’s no official way to do this, and it doesn’t seem like the PS4 ever updates controllers. At least not in a way that’s obvious to users. Of course, you should make sure your PS4 itself always has the latest system software, but we can’t find any evidence that this would affect controllers directly.
While there are third-party tools to reflash the firmware on PS4 controllers, these are mainly used by modders and aren’t relevant here.3. Check the Charger and Cable
An essential troubleshooting step is ensuring your cable and charger work properly. Try a different one or try charging something else with it. The same goes for the cable. Use a different cable to see if that makes a difference.
Another potential issue is using a fast-charging port. For example, some power banks offer standard USB and fast-charging ports. In our experience, the DS4 won’t always charge from these intelligent fast-charging ports but will happily charge from a standard USB port.4. Use the Controller Wired
While it’s not a solution to the battery charging issue, you can use a long micro USB cable to power your controller directly from your PS4. You can also use a power bank to power the controller while using it wirelessly.
This is a stopgap until you can get the charging issue sorted, but at least you can keep playing in the meantime!5. Check the Controller Charging Port Connector
The micro USB port on the PS4 controller will wear out over time as you repeatedly insert and remove the charging cable. This is one of the reasons the PS5 controller has zero-friction pins for charging in addition to a USB-C port.
Inspect your PS4 controller and see whether there’s any dirt or debris inside the port. If you see grime in there, you can dislodge it with a can of compressed air. Ensure you use the can as indicated to avoid creating moisture inside or damaging the USB port.
Insert the micro USB cable into the controller and gently wiggle it to determine if the port is loose and broken inside. If the port has broken loose on the inside of the controller, it may be possible to have it repaired by a professional if you don’t feel confident in your soldering skills.
If the plug slips in and out of the micro USB ports too easily, the port may have worn out to the point where consistent contact is impossible. In this case, you may have the option to replace the port with a new one, but weigh up the cost and effort of doing this against the price of a new controller. If you’re satisfied after inspecting the controller for signs of damage, it’s time to try something else.6. Reset the Controller
You can reset your PS4 controller with a dedicated hardware button, which often resolves some seemingly random issues that can crop up with the device. You only need a plastic or wooden toothpick or another object that won’t damage the plastic.
Flip your controller upside down, and locate this recessed reset button near the L2 trigger on the back of your controller.
Image Source: Sony
Use your tool to depress the button inside the small hole for 5 seconds.
Now the controller has been reset. To pair it with your PS4, connect it to the console using a USB cable and press the PS button. To use it with another device, like a PC or iPad, you’ll have to pair it again as a new Bluetooth device. If you’re unsure how to do that, check out How To Connect a PS4 Controller To An iPhone, iPad Or Android Device.7. Do a Warranty Return (If Applicable)
If your PS4 controller is still under warranty, you shouldn’t mess with it. Instead, get in touch with the store you bought it from or with Sony’s customer care department, and have the controller repaired or replaced under its warranty. You’ll be without your controller for a few days, but at least you know you’ll get a working unit back.8. Replace the Controller Battery
All lithium batteries wear out over time. If your PS4 controller is a few years old, it no longer has full battery capacity. If the battery wears out enough, it eventually won’t hold a charge. However, if the rest of your controller still works fine, you can replace the PS4 controller quite easily. The battery isn’t glued in or soldered to the internals of the controller.
An Example of a Third-party Battery
We strongly recommend you watch a YouTube video on replacing the battery before attempting it. You can find third-party replacement batteries on sites like Amazon, but pay attention to the reviews and ensure the new battery is reputable. Unfortunately, original Sony batteries are tricky to find, so a third-party option may be your only choice. You can take this as an opportunity to put a larger capacity battery in your controller, though!9. Add an External Battery Pack
If you don’t feel comfortable opening up your PS4 controller, a clip-on external battery pack is another workaround for a worn-out battery. For example, the KMD Battery just pops into your controller and adds 1000mAh of power. That’s just as much as the PS4 controller shipped with, so you’ll get at least the original capacity back, plus whatever the original battery still has.10. Buy a New Wireless Controller
If your PS4 controller is in rough shape overall, doesn’t charge or turn on no matter what you do, or simply can’t find a suitable battery replacement solution, it’s time to accept that you must buy a new controller.
However, this doesn’t mean you must stick with a Sony original. The PS4 has been around for quite some time, and many excellent third-party alternatives solve many of the small complaints people have about Sony’s otherwise excellent controller.
For example, the PDP Victrix Pro BFG controller offers an offset layout like Xbox, works with PS4 and PS5, and can work as a PC controller. Although it has no rumble or haptics, the battery life on this controller is rated at up to 20 hours, and it has heaps of extras such as back buttons and multiple custom profiles.
If the asking price on the BFG is a little dear for you, then the TERIOS controller does an admirable job of cloning the DualShock 4 at a shockingly low price. It’s comfortable, has programmable back buttons, and has better battery life than the original Sony controller, but the quality of the rumble isn’t quite as good. If you don’t care for rumble and want to save a few dollars, it’s a great option.
If, on the other hand, you’re feeling a little flush with cash, you could go for something like the NACON Revolution Unlimited Pro V3. It has a seven-hour battery life, customizable sticks, and a 10-foot cable if needed. This controller is more about performance than comfort, but it’s a great start if you want to take your competitive gaming more seriously.
You're reading Ps4 Dualshock Controller Not Charging? 10 Ways To Fix
The PS4 controller has a light bar showcasing its functional state. If it’s working normally, it shines with white light. But I’m guessing this is not the case for you, so you’re wondering why your PS4 controller light is red.
The red light on a PS4 controller is often a sign of physical damage. It means broken hardware, and it’s typically the USB port on the back of the peripheral.
However, a random bug or a normal function may also be causing the issue. For example, if your DualSence was working fine until you suddenly saw a red light, it’s not something to worry about.
But if it has been stuck like that for a while, and it doesn’t work or sync to the PS4, you may need some troubleshooting.Why Is the PS4 Controller Light Red?
If your PS4 controller light is red, it could be a normal function or a problem you need to solve.
Like the lights on the PS4’s body, the controller also indicates various states with its light bar.Normal Functions of the PS4 Controller Red Light
There’re cases when the shining light is part of its proper functionality. Most of all, the PS4 controller light may turn red during gameplay without presenting any further issues.
First off, some games like The Witcher 3 can change the light bar’s color as you play. If this is your case, it’s completely normal.
Other titles use the controller’s red light to indicate the character’s health. Another example is some Need For Speed games, as the controller’s light will turn red if you die in a Killzone.
Another example: In GTA V, the light bar shines in a different color for each character (yellow for Trevor, blue for Michale, and green for Clinton).
The light also changes color if you’re playing local co-op on the PS4:
Player 1: Blue light
Player 2: Red light
Player 3: Green light
Player 5: Pink light
Lastly, if you’re the only player and the controller’s light is red, it could mean you’re logged as another user. Changing the user to the console’s main account will change the light color.Possible Errors When PS4 Controller Light Is Red
Sadly, the red light may also indicate errors. It’s easy to tell because it’s a red light that keeps flashing and doesn’t change. Also, most probably, the controller is not able to charge.
If this is the case, you may be dealing with one of these problems:
Your PS5 controller’s hardware is broken. The error is commonly a faulty USB port that won’t allow your controller to charge on the console.
You’re dealing with a faulty ribbon cable. Your controller has a ribbon cable within its body, and it’s a necessary part of the USB port. When it’s not functioning properly, the controller can’t charge.
There’s a loose connection between the battery and the part. Perhaps the battery is not properly connected to the port. It may happen if the controller suffered physical damage recently.
The battery is malfunctioning. If your PS4 is over four years old, you should expect your PS4 controller battery to break and require a replacement.
There’s a random firmware bug causing the issue. It may prevent your controller from charging properly.How to Fix PS4 Controller Light Is Red
Here’re various situations where you could see the PS4 controller red light. If you identify your problem, finding the solution you need from the list below may be easier.
The PS4 controller light is red, but the controller is working. Even if the red light blinks continuously, you can still plug and use it, but it won’t charge. The solution is plugging the cable back in to secure the connection.
The PS4 controller light turns red only when connecting it to the console. It means it has problems when charging via the console. If you have already replaced the charging cable, you need to reset the console and the controller.
The red light won’t turn off after you shut down the console. It often indicates a hardware issue or a firmware issue. If resetting the controller doesn’t work, you’d need to reset the console via Safe mode. Otherwise, you’d have to replace the USB port, the battery, or the ribbon cable.
The red light blinks continuously, and the controller won’t connect. This means the USB port or the USB cable is not working properly. It could also mean the peripheral internals malfunction, like the ribbon flex cable.
The red light blinks, and then the light bar shuts off. It indicates a firmware issue. A console and controller reset will do the trick.
The red light is blinking, and the controller is vibrating. If your controller suffered physical damage recently, or if you dropped it in water, the battery may be damaged. Draining the console’s entire power may do the trick. Otherwise, a battery change will fix it.Reset the Controller’s Firmware
Let’s hope you’re dealing with a firmware bug, as it’s the easiest problem to solve. Simply, you have to push a button on the controller to restore it to factory default.
Turn off your console.
Unplug the controller.
Unplug all of the console’s cables, and wait for five minutes. This is a power cycle to help further erase problems.
On the back of the controller, near the L2 button, there’s a hole that hides the reset button. Push it with a pin or a similar sharp object. You need to hold it for about seven seconds .
Plug the console’s cables back (after five minutes).
Plug your controller into the console via its USB cable.
Turn on the console.
Press the PS button on your controller to turn it on.Initialize the PS4 in Safe Mode
Let’s keep assuming it’s a bug, so we’re restoring your PS4 to factory settings via its Safe Mode troubleshooter. The process won’t erase your data, but it may take a while.
Shut down your PS4.
Do a power cycle (unplug all of its cables for at least a minute).
Plug back the cables.
Press and hold the power button on the console for about 10 seconds until you hear a second beep.
Plug the DualShock into the console via its USB cable.
Press the PS button to start Safe Mode.
Select option 6: Initialize. It will ask you if you want to keep your data and apps. Alternatively, you can choose option 1: Restart, as it will re-launch the system while attempting to erase errors. If this doesn’t work, go back and try option 6.
Wait for the process to finish. It will restart the console.Drain the Battery
The next logical option is unplugging the charging cable from the power dog for a minute. It allows the controller to cycle power and release random firmware bugs.
Your next option is draining the console’s power to reset the connection with the controller:
Shut down your PS4 controller by pressing and holding its power button for 5 seconds.
Unplug all of the console’s cables for 5 minutes.
Unplug the USB cable from the controller.
Press and hold the console’s power button for 30 seconds to drain leftover energy.
Plug all of the cables back.
Plug the controller into the console with the USB cable.
Turn on the console, and press the PS button on the controller again.Replace the Charging Cable
Let’s hope you can also fix it by changing the charger cable. First, though, check the PS4’s cable for physical damage.
Then, if you connect the PS4 to the console with a new cable, and its light turns orange, it means it’s charging. And when it turns green, it’s fully charged.Take Your Controller for Repairs
If the issue persists, it means the internal suffered damage. Like I’ve said, it could be the battery, the ribbon flex cable, or the USB port.How to Fix PS4 Controller Red Light on PC
If you’re using the PS4 controller on a Windows PC, the red light means the controller is working with high latency.
Easy solutions include plugging the controller into a USB 2.0 or a USB 3.0 port. If you’re using it on a USB 1.0 or via Bluetooth, the latency will likely surpass 10ms.
A PS4 controller flashing orange means your console is in Rest Mode or is charging. See, the device uses its light bar to display information, and an orange light doesn’t always mean it’s something bad.
But if the light remains orange as you play, or if it turns steady orange, you may need some troubleshooting. Other times, it often speaks about random bugs, power issues, and lag problems.Why Is PS4 Controller Blinking Orange
The orange light could be normal or refer to a problem. You will identify it’s an issue if you start noticing other symptoms or malfunctions.
Here’s the summary:
A yellow or orange blinking light means the controller is charging on the PS4 while the PS4 is on rest mode.
A steady yellow or orange light means the controller is connected to the console, but it’s not charging. It happens because the PS4 is shut off or in Rest Mode. You can enable controller charging while on Rest Mode, which, in turn, would make the orange light blink.
Additionally, the lightbars color represents different users during co-op gameplay. However, the orange color is not part of the list:
Player 1: blue lights
Player 2: red lights
Player 3: green lights
Player 4: pink lights
So far, it’s normal for the PS4 controller to have a blinking orange or yellow light. You’d need to keep an eye for additional issues and clues about what’s happening.
So, common dysfunctions that can happen alongside a blinking orange light are:
The controller is lagging (timing problem)
The battery can’t charge properly. In particular, the controller starts flashing in orange when it’s charging but stops blinking before it gets a full charge.
The controller has a power problem, so it loses charge too quickly or shuts off randomly.
Your controller can’t connect to the console. It often relates to a bug on the peripheral or the system.
There’s internal damage, which presents itself in many ways. That includes erratic behavior, non-functioning buttons, or failing to sync with the console.How to Fix PS4 Controller Blinking Orange?
Overall, a blinking orange light may come with connectivity and charging issues. You’d recognize you’ve fixed the issue with the controller’s status lights:
It blinks orange when you connect it to the PS4 if it needs a charge
The light shines steady white or blue when you use it.
Here’re some easy troubleshooting steps:Power Cycle the Console
The first logical step is power cycling the console. It will erase arbitrary power bugs preventing your controller from charging:
Shut off the console by pressing and holding the power button for five seconds.
Unplug all of its cables for 5 minutes.
Plug back all of the cables.Reset the Controller
After power cycling the console, you must reset the controller. It puts the firmware back to default, which erases bugs causing timing issues, erratic behaviors, and syncing errors.
Here’re the steps:
A solution users share on forums is re-syncing the controller automatically. However, you need another controller for the process:
Plug another working controller on the console.
Turn the console.
Go to Settings.
Go to Devices.
Choose Bluetooth devices.
Take your faulty controller and press and hold the Share and PS button simultaneously for about 5 seconds.
Check if the peripheral appeared on the Bluetooth devices menu. It should have a green dot indicating the console identified the device.Hard Reset the Controller
If the above solution didn’t work, let’s try taking the controller’s firmware back to default. It will fix the issue 99% of the time.
Power cycle the console.
Unplug the controller from the console.
Press the reset button at the back of the controller. Use a pin to push and hold the button for 5 to 7 seconds.
Plug back your controller to the console.
Press the PS button to turn on the PS4.
You can unplug the controller now and test if it works normally.
If your controller functions at this point, it will display a blue or white light. It would mean you were dealing with a bug.
Otherwise, let’s try the next step.Enable Charging on Rest Mode
Let’s try recharging the battery for a while. If it’s completely out of charge, it can take about 2 hours to come back to life. So, you must leave it charging for 3 hours, at least.
On your PS4, go to Settings
Go to Power Saving Settings
Select Set Features Available in Rest Mode
Select Supply Power to USB Ports, and choose, for example, “Three Hours.”
After leaving your peripheral charging for three hours, test it against and see if the light turns white.Change the Usb Cable and the Usb Port
The problem may be the power supply circuit. It presents itself with the light bar blinking orange when it’s charging but stops before a complete charge.
You can verify it by using another USB Type-C cable to charge the controller. Cables are easy to fail.
Additionally, you could try another USB port from the PS4. These are prone to failure.Soft Reset the Console
A soft reset is simply restarting a device. It allows electronics to flush and cycle issues, settings, apps, processes, caches, RAM, and protocols. It’s like taking a CD out of your console, putting it back in, or taking out the older Nintendo cartridge to blow air in the pins.
Here’s how to do it:
Press the Eject and the Power button on the console and the same time for about 30 seconds. The PS4 will emit two beeps before shutting down
Press and hold the power button to turn it back on
Plug your controller back and test itHard Reset the Console
If there’s a bug on the console preventing communication with the controller, let’s try taking it back to factory settings via Safe Mode.
It won’t erase your data and apps, but it will erase your settings. Also, it may take some time, but it can potentially save you the cost of a repair or a new controller.
Here’re the steps:
Turn off the console by holding the power button for three seconds.
Press and hold the power button again for about seven seconds until you hear a second beep.
Connect the controller to the console via USB cable, and press the PS button. If your faulty controller doesn’t respond, try using another one. Otherwise, try using another cable or another USB port.
Select option 4: Restore Default Settings.
After the process finishes, the console will restart normally. Now, check if the controller is working normally. You’d also need to check if it charges properly:
Enable Supply Power to USB Ports as I showed below.
Press and hold the controller’s PS button.
Choose Enter Rest Mode from the pop-up menu.
Check the lights on the controller. If they are blinking orange, it’s charging; if they are steady orange, it’s not charging; it’s okay if the light is solid white or blue.Send Your Controller for Repairs
If the issue persists, you’re dealing with internal damage. The typical symptom is your controller can’t charge completely or at all.
Commonly, the failure is the USB-C loading port itself. Only a professional would be able to change it.
However, other internal electronic components may fail, causing additional issues with your controller. For example, a problematic part is the conductive film, the controller’s circuit board.
Another possible culprit is the internal ribbon flex cable. It registers button commands, and it’s prone to failure. In particular, a damaged flex cable also causes lag problems.
You can check whether your problem is either the ribbon flex or the conductive film by holding the Share button. If the light blinks, it means there’s internal damage. If it doesn’t, you could resolve the issue with one of the solutions above.
If you’ve found weird behaviors and the solutions below didn’t do a thing, you’re facing some kind of internal damage. Again, the answer is to send your controller for repairs.Can You Change the Components Yourself?
If you’re a hands-on, tech-savvy type of person, you could try changing the internal components yourself.
Here’re the tools you’d need:
A plastic pry
A Phillips head screwdriver or a very tiny cross-head screwdriver
A small clip
Rubber gloves to avoid static shock
Then, you would need to fully open the controller. Use your plastic tool to pry open the case very carefully.
Once open, you should check the ribbon cable. It should line correctly between the upper side of the case (the buttons) and the circuit board. If you see any damage, you’ll have to change it.
Also, ensure the USB port makes a proper connection with the circuit board.
Maybe it’s too loud in your home to hear the TV properly, or you just want to keep the volume low. Either way, there are times when subtitles or closed captions are the best options for enjoying a streaming show. When HBO Max subtitles aren’t working, there are several things you can do to fix them.
Maybe the subtitles are out of sync, or they aren’t appearing. Whatever the cause, you can take steps to get them back on screen (and appear like they’re supposed to).
Table of Contents1.
Check HBO’s Server Status
If the HBO Max servers are down, the streaming service might not behave as expected. The first step you should take is to check Downdetector. It will show you whether HBO Max is having a problem in a localized area or if the service as a whole isn’t operational. If this is the case, all you can do is wait for it to come back online.2.
Check Your Ping
While HBO Max requires sufficient internet speed to stream video, it also needs a quick response time from the server to your device. This response time is called ping (or lag, for gamers out there). You can check this by going to chúng tôi and running a speed test. It will show you your download and upload speeds and your overall ping in milliseconds.3.
Disable Your VPN
While a VPN (virtual private network) provides security while browsing the web or accessing sensitive information, it can interfere with streaming services. While a VPN makes it possible to access programming from other regions, you should disable it while streaming if you encounter problems with your subtitles. Turning off the VPN is sometimes all it takes to correct these issues.4.
Reboot Your Streaming Device
It doesn’t matter whether you’re streaming on a Firestick, macOS, Android TV, Xbox, or Roku device – sometimes, the easiest fix is to turn it off and back on again. A quick power cycle will fix most glitches and let you experience the content the way you want to.5.
Update or Uninstall and Reinstall HBO Max
When you’re using HBO Max on a mobile device, whether Android or iPhone, there are two things you should check. First, make sure you’re using the latest version of HBO Max. If you are and the problem continues to persist, uninstall the app and reinstall it. Often, a botched installation or update will cause glitches that can’t be explained. Completely reinstalling the app will fix these.6.
Clear Your Web Browser Cache
Try clearing your browser cache if you’re streaming through the HBO Max website. How you do this varies depending on your browser, but wiping the cache and restarting the browser will often fix most problems you run into.
Ensure the box for “Cached images and files” is checked, then select
7. Clear Your App Cache
If you’re streaming through a mobile device or an iPad, try clearing your app cache. This serves the same function as clearing your web cache. While the exact approach varies between devices, they all follow a basic process.
On Android, you can clear the cache by accessing the HBO Max app, selecting Clear Data, and then Clear Cache. On iOS, you can’t clear the specific app cache, but you can delete and reinstall the app. It has the same result in the end.
8. Check Your Caption Settings
Make sure you actually have subtitles enabled.
While streaming, select
. This looks like a speech bubble.
English – Original
Refresh the video.
This will turn on subtitles and start streaming them alongside the audio. Too often, it’s easy to forget to select the CC button, especially if you swap between streaming platforms. Even if it’s enabled on one, it might not automatically be enabled on another.
9. Try a Different Device
If you can’t get subtitles to work on one streaming platform, try another. For example, try streaming on your Roku device if HBO Max subtitles won’t load on your smart TV. Sometimes, server issues might prevent subtitles from working for one platform and not another, even if there are no reported problems.
Roku devices often have different settings than your mobile app. You might have enabled or disabled a setting on one platform that’s still enabled on another.
10. Report to HBO Max Help
If you’ve tried every possible step and still can’t get subtitles to load, report the problem to HBO Max. You can reach them through messaging, phone, or email by going to the Help Center. Subtitles aren’t generated automatically; they’re uploaded as part of the data with a specific TV show or movie. So it’s possible that some of the data is corrupted, resulting in subtitles appearing incorrectly or at the wrong time.
If this happens, you can’t fix the problem yourself. HBO Max will have to take care of it from their end, but they need to be aware of the problem first.
Subtitles are a boon to the hearing-impaired, so it can be particularly frustrating when they don’t work. Try these fixes to get back to watching your favorite content.
It does not sound good, literally, if the left speaker of your PC does not work.
You may not be receiving output from the left speaker unit for a few reasons. There can be inappropriate sound settings, faulty audio drivers, or simply fault in the hardware. However, before that, look for a volume change button or scroll bar on your left speaker and see whether it is at its lower level. If it is, try raising the volume.
But you probably already did that. So, we are here to help you fix the issue on your PC’s left speaker.
Are you sure that your speaker is not damaged? Use the speaker on another computer and see if the issue persists there. You can also try connecting another speaker to your PC to identify the problem.
If it works there and you are sure it is not the speaker, let’s look at the fixes right away.
Sometimes the left speaker can fail to emit sound due to loose connections. For instance, if you insert the audio jack to only half its length, you may not hear sound from one of the speakers. So, you should inspect the speaker cables and the ports to check their integrity.
Run an audio clip on your PC and do the following to see what solves the issue.
Disconnect the audio plug or USB plug from your system and reconnect it.
Try using different ports to find any issues with them while connecting the speaker. If you had used the front port, then insert the cable to the one at the back and vice versa.
If your speaker also uses a removable jack on its unit, then see if the left speaker cable is properly connected.
Wiggle the cable and connector at both ends, PC and left speaker, to observe if the audio restores in the left one.
Exchange the audio cables used in the right and left unit and see if the left speaker works with the exchanged cable.
If you have connected your speakers through Bluetooth, check whether the left and right speakers are paired. Sometimes, another device may be using the left speaker.
Rectify the problem accordingly after finding the issue. For example, if the speaker worked while wiggling the cable, then the cable is probably damaged, and you will have to replace or repair it.
Windows has a feature to balance the volume level for an individual speaker. So, you should check if the left one is muted or is at a very low volume.
Let’s see how you can do it.
Play a sound to see if the left speaker is working again.
The audio devices are operated by the Audio system service on your PC. If it is malfunctioning for any reason, you may find the left speaker not working. So, you will have to restart the audio service.
Reboot your PC and see whether the speaker works properly now.
Sometimes, the audio device may not be able to communicate with its driver software properly. You should disable and restart the audio device to solve the problem.
Let’s see how you can do it.
See if the left speaker has started to work again.
If disabling the device does not work out, there may be issues with the device drivers. So, you will have to update or re-install them on your PC.
Let’s look at the way to update the audio drivers.
Reboot your system and see if it solves the issue.
You will have to uninstall the drivers if updating it does not do the job. But simply uninstalling them does not remove the cache and configurations. You can use Display Driver Uninstaller (DDU) to perform a complete uninstall.
You should hear the audio from the left speaker now.
Your PC may be using various enhancement configurations to improve the sound quality. Mostly, this really improves the audio experience. But sometimes, these enhancement settings may interfere with the speakers. So, you can try disabling it.
Similarly, some apps may be using your speaker and modifying its settings. So, we recommend you do not allow other applications to take control of the device.
Notice if sound emits from the left speaker now.
You can run Windows built-in troubleshooter to identify the bugs and resolve them. Let’s see the way to run the Audio troubleshooter.
If it finds any error, then the troubleshooter will automatically resolve it.
Some laptops and PC manufacturers provide a separate program to check the health of the hardware, like the ePSA test in Dell. So, you should look at the device manual and website to see if your laptop or speaker has such an option.
If yes, then run the hardware troubleshooter to fix the issue.
It may just be that the drivers or system services to control the audio device are corrupted. Or, some virus may be causing the device to malfunction.
You can perform an in-place upgrade to resolve the issue. Let’s go through the process together.
See if the speaker works now.
Speakers and your PC coordinate to provide the best sound experience. To do this, there are several audio modes, especially Mono and Stereo. Mono mode combines the sound from both into one, while Stereo mode sends audio from each speaker separately.
Sometimes, the mono mode may fail to combine the channels, or the Stereo mode may not receive sound from both ends. Few users have reported that changing the audio mode fixed the issue. So, you can try to do that.
See if both speakers work in either mode.
Apple syncs messages from your iPhone to Mac (and vice versa) if both devices use the same Apple ID. If you don’t receive iMessages (or text messages) on your Mac, the troubleshooting solutions below should fix the issue.
Your Mac may not synchronize messages and other iCloud data over slow or unstable internet. Ensure your Mac has internet access before attempting to fix iMessage’s synchronization issues.
Table of Contents1. Check Apple ID and iMessage Server Status
Head to the Apple System Status web page in your web browser and check the indicator next to iMessage and Apple ID.
A green indicator means both services are working correctly, while yellow or red means they’re temporarily unavailable.
Apple ID and iMessage work hand-in-hand—Apple uses your Apple ID to sync messages across your devices. Your Mac may not synchronize messages from your other devices if the iMessage or Apple ID server is down.
Apple fixes server-related issues in time, so messages from your other devices will sync to your Mac when iMessage’s back online.2. Check Apple ID and iMessage Address
Ensure your Mac uses the same Apple ID account and iMessage address as your other devices.
on the menu bar, and select
Open the iMessage settings tab and check that the Apple ID is the same one connected to your iCloud devices.
Also, ensure there’s a checkmark next to the iMessage email address or phone number.
if the Apple ID doesn’t match the account on your iPhone or iPad. Your Mac will sync your messages when you sign in to the same Apple ID on your other Apple devices.3. Check Your Date and Time Settings
Apple may not sync messages to your Mac if its date and time settings don’t match your current location. Connect your Mac to the internet and set the date and time using Apple’s time server.
Date & Time
Head to the “Date & Time” tab and select the
in the bottom corner.
Enter your Mac’s password or use Touch ID to unlock the Date & Time preferences page.
Set date and time automatically
Select the “Time Zone” tab and check
Set time zone automatically using current location
.4. Manually Sync Messages
macOS has an option to sync conversations from your iCloud devices to your Mac manually. Initiate a synchronization if your Mac doesn’t update conversations automatically. Connect your Mac to a Wi-Fi network and follow the steps below.
on the menu bar, and select
Head to the
tab and select
The synchronization speed depends on your internet connection speed and how many messages your Mac’s synchronizing. Wait 2-5 minutes and check if conversations in the Messages app are up-to-date.5. Re-Enable Messages in iCloud
Reactivating the messaging service on your Mac can also fix the synchronization issue.
on the menu bar, and select
Go to the
tab and uncheck
Enable Messages in iCloud
Disable This Device
on the confirmation window.
Enable Messages in iCloud
You should see a “Downloading Messages from iCloud” progress bar at the bottom of the Messages app window. The missing messages or conversations should appear on your Mac when the download is complete.6. Enable Text Message Forwarding
If you don’t get text messages on your Mac, check that “Text Message Forward” is enabled on your iPhone.
Open your iPhone’s Settings app, tap Messages, select Text Message Forwarding, and turn on text message forwarding for your Mac.
Your devices must use the same Apple ID for text message forwarding to work. If your Mac isn’t on the message forwarding page, link your Mac to your iPhone’s Apple ID and check again.7. Reboot Your Devices
Shutting down your computer and turning it back can fix synchronization glitches and other Mac issues. Ensure you close all applications before rebooting your Mac, so you don’t lose unsaved data
Select the Apple logo on the menu bar and select Restart on the Apple menu.8. Disable and Enable iMessage on Your iOS Device
Re-enabling iMessage on your iPhone or iPad can restore message synchronization to your Mac.
Wait for your network carrier to activate iMessage and check if your device now syncs messages to your Mac. Learn what to do if your device gets stuck in the “Waiting for activation” phase.9. Update Your Devices
Apple often releases iOS and macOS updates introducing new features and fixing issues with Apple apps and services. Update your devices’ operating system to the latest version and check if messages now sync to your Mac.Your iPhone Could Be the Culprit
If the problem persists, your iPhone or iPad is probably not uploading/syncing your messages to iCloud. Get iMessage working correctly on your iPhone and Apple will sync messages across your devices without issues.
Update the detailed information about Ps4 Dualshock Controller Not Charging? 10 Ways To Fix on the Katfastfood.com website. We hope the article's content will meet your needs, and we will regularly update the information to provide you with the fastest and most accurate information. Have a great day!